-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Quiet Power: Evaluating Evaluation Boards
September 28, 2016 | Istvan Novak, OracleEstimated reading time: 2 minutes
Evaluation boards are very helpful. Manufacturers of complex circuits such as DC-DC converters provide boards with those circuits ready to try out, saving us time and effort to design the printed circuit board around them. Evaluation boards are supposed to help us to understand the capabilities of the device. But with the many potential user applications, what should a particular user expect and look for in an evaluation board? We need to know how to properly evaluate an evaluation board.
My February 2013 Quiet Power column featured an LTM4604 evaluation board. In that column the purpose was to discuss different measurement techniques; the subject was not the regulator itself. In this column we look at an LM20143 evaluation board to explain what may matter during the evaluation.
The LM20143 is an adjustable-frequency synchronous buck regulator with current-mode control loop [2]. The input voltage can be anywhere in the 2.95 to 5.5V range, the maximum continuous output current is 3A. The switching frequency is adjustable in the 500 kHz to 1500 kHz range. The default output voltage setting of the evaluation board is 1.2V. The integrated circuit includes the output switching devices. Figure 1 shows the top view of the evaluation board with no cable attached. To make the board work, all we have to do is connect a voltage source to the input terminals and pull the enable pin (labeled ‘EN’ on the board) to logic high.
The first rule in every test and measurement (also true in simulations, by the way) is “Know what to expect.” We measure something because we may want to validate a design or we measure something because we are not sure exactly how the circuit behaves. This latter case, however, is no excuse to ignore the rule: we still should have some idea what we expect as a result. If we don’t, it becomes a full-fledged exploration and we need to be extremely careful to make sure that accidental mistakes or measurement errors don’t mask the correct signature that we are after. In an evaluation board of a DC-DC converter, we can test many different aspects of operation. There are items that require only DC voltage and current meters. This way, for instance, we can check the line and load regulations and efficiency at different input and output voltages and load currents. To test for dynamic parameters, we can use an oscilloscope and transient current source. In the frequency domain, with a frequency response analyzer or vector network analyzer we can test the gain-phase curve or output impedance. These measurements can be done with small-signal excitation or large-signal excitation.
To read this entire article, which appeared in the September 2016 issue of The PCB Design Magazine, click here.
Suggested Items
D Coupon Testing and Data Insights With GreenSource Fabrication
04/17/2024 | Marcy LaRont, PCB007 MagazineMarcy LaRont spoke with Steve Karas of GreenSource Fabrication at the SMTA UHDI conference in March. He presented a case study that GreenSource undertook with a customer on critical via reliability with advanced materials and used the experience to highlight the importance and effectiveness of D coupon testing. He also discussed GreenSource’s approach to data aggregation and a new system they developed to use collected data effectively.
Three Industry Leaders Receive IPC President’s Award
04/17/2024 | IPCIn recognition of their leadership and significant contributions of time and talent to IPC and the electronics industry, three IPC volunteers were presented with the IPC President’s Award at IPC APEX EXPO in Anaheim, Calif., on April 9, 2024.
Yamaha to Showcase Latest-generation Assembly Equipment and Software Tools at SMTconnect
04/16/2024 | Yamaha Robotics SMT SectionYamaha Robotics SMT Section will team with its distributor ANS Elektronik to showcase innovations for high-speed surface mount assembly at SMTconnect 2024.
TT Electronics Awarded Contract with Kongsberg Defence and Aerospace
04/11/2024 | TT ElectronicsTT Electronics, a leading provider of global manufacturing solutions and engineered technologies, announced today that its Fairford UK business has been awarded a new contract with long-standing customer Kongsberg Defence and Aerospace (Kongsberg) for the production of complex cable harness solutions.
Infineon, Amkor Deepen Partnership and Strengthen European Supply Chain for Semiconductor Solutions
04/10/2024 | InfineonInfineon Technologies AG, a leader in power systems and IoT, is strengthening its outsourced backend manufacturing footprint in Europe and announced a multi-year partnership with Amkor Technology, Inc., a leading provider of semiconductor packaging and test services.