Predictive Engineering: Happy Holden Discusses True DFM


Reading time ( words)

Happy Holden has been involved in DFM for over 45 years, since he first started working at HP and optimized their PCB design and manufacturing processes. Naturally, for this issue, Barry Matties and Andy Shaughnessy made it a priority to get Happy’s thoughts on DFM, and what true DFM entails.

Andy Shaughnessy: Happy, why don’t you start by telling us about your position on DFM, and why true DFM, to you, means that PCB designers and engineers should utilize predictive engineering.

Happy Holden: If you use the term “predictive engineering,” you're not going to get much recognition, because that's a term I use. What most people consider design for manufacturing, or DFX, is software that finds errors in design. Especially in CAM tooling put out by Valor, if a manufacturer puts in his design builds in a minimum, then the DFX software scans through that and finds what’s cautionary and that all requirements are met. That's all done after the fact.

For me, DFM was introduced when HP took up DFM. It was kind of invented by Professors Peter Dewhurst and Geoffrey Boothroyd. Anyway, DFM and DFMA (design for manufacturing and assembly) were really invented by these two American professors in New England. They wrote a book about it, Product Design for Manufacture & Assembly. It later became software.

Their whole philosophy centered on ways to figure out how to do it right the first time. Their book is about the nature of performance during design that allow you to decide if this is going to be easy to assemble. I think the more important component, that Hitachi and the Japanese took it up, was whether the product could be built by automation? That's really significant what Hitachi did with the philosophy. They not only took the ‘do it right the first time’ approach but then asked how they could do it simple enough that robots and automation can build it? The Japanese did this because they wanted to build all these first-generation products in a building next door in Japan and not ship it offshore like Americans were doing.  

Contrast that with Apple Inc. Apple designs products that are impossible to automate. They're so complex. They're really fanciful, but they have to be built by human hands. You've got 86,000 17-year-old teenage girls in Shenzhen building these Apple products. Foxconn put up money to install 1 million robots to replace these girls. Today only about 400 robots have been installed out of that 1 million, because they found out the products they're building for the Americans can’t be automated.

I refer to DFM as being designed for manufacturing the first time. We're not just designing it, running software, finding the errors, going back, redesigning it, checking again, going back and re-spinning it, until it works. I'm alone in this definition unless you happen to be knowledgeable about Dewhurst and Boothroyd, which most people in printed circuits aren't. 

To read this entire article, which appeared in the September 2017 issue of The PCB Design Magazine, click here.

Share


Suggested Items

Video from productronica 2017: Karel Tavernier on Ucamco's New Communic8tor

11/20/2017 | Pete Starkey, I-Connect007
European Editor Pete Starkey and Ucamco Managing Director Karel Tavernier discuss Ucamco’s cloud-based Communic8tor platform which facilitates two-way communication between the CAM engineer and the PCB designer, or any other party involved in the manufacturing process. This gives real-time access to image data and annotations, enabling queries to be resolved, changes to be approved, and a full communications history to be maintained.

Happy Holden and Charles Pfeil Discuss the Past and Future of PCB Design, Part 1

11/07/2017 | Barry Matties, I-Connect007
When it comes to the PCB design community and the challenges facing it, as well as where design has been and where it’s heading, there aren’t many people as qualified to speak on the topic as long-time industry veterans Happy Holden and Charles Pfeil. Joined by I-Connect007’s Barry Matties at the recent AltiumLive 2017 event in San Diego, the three sat down for a discussion about the current state of PCB design, what the future holds, and what it means to be a designer.

The History of Predictive Engineering

11/01/2017 | Happy Holden, I-Connect007
It all started in 1983, at HP, when I complained to our group's vice president that our W. Edwards Deming and Total Quality Management (TQM) Six Sigma training was being concentrated in PCB manufacturing. We had eliminated final inspection and instead placed quality in the hands of the operators with a final electrical test. The electrical test was governed by what we learned from Deming.



Copyright © 2017 I-Connect007. All rights reserved.