-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Thermal Management Update with Doug Brooks
January 22, 2018 | Andy Shaughnessy, PCBDesign007Estimated reading time: 1 minute
I had the opportunity to talk with our contributor Doug Brooks recently. He has been doing some research on temperature effects on PCB traces over the last few years, and I wanted to check the status of his latest thermal efforts. He discussed his work with Dr. Johannes Adam, why temperature charts based on a trace in isolation are inaccurate, and how the industry remained so wrong about PCB temperatures for so long.
Andy Shaughnessy: You have done some work on thermal management lately. How did that project start?
Doug Brooks: I wrote an article in the mid-‘90s on trace current/temperature effects, and I used two data sources: the then-current IPC data and some data I found in a 1968 Design News (DN) article. The DN temperatures were about 30% to 40% higher than the IPC temperatures and I wondered why. I began to suspect that it was because of the differences in the way the temperatures were measured or calculated. In looking for a way to confirm that hypothesis, I ran across an article about three years ago written by Dr. Johannes Adam in Germany, and I contacted Johannes.
It turns out that Johannes had written a computer simulation program called TRM (Thermal Risk Management) that was well suited for me to use to look at the data I had used in the article. He offered me a license for the software and we used TRM to simulate the IPC trace data in IPC-2152 and also the earlier data from DN. The simulations were very successful.
Shaughnessy: What did you find out?
Brooks: It turns out the DN data were unreliable!
Shaughnessy: And all of this took place over several years?
Brooks: No. That was just the beginning. It was so easy to simulate the IPC trace data that we began to simulate more realistic scenarios. The IPC data apply to a 6-inch trace in isolation. We began to look at what happens when we change things: change the length, change the pad sizes, add additional adjacent traces, add planes below the trace or on the other side of the board, more common layout conditions like those.
To read this entire article, which appeared in the December 2017 issue of The PCB Design Magazine, click here.
Suggested Items
IPC Raymond E. Pritchard Hall of Fame Award: Pierre-Jean Albrieux
05/10/2024 | Marcy LaRont, PCB007 MagazineCongratulations to Pierre-Jean Albrieux, who received the 2024 IPC Raymond E. Pritchard Hall of Fame Award. The award is given to individuals in recognition of the highest level of achievement, extraordinary contributions, and distinguished service to IPC and toward the advancement of the industry, including helping to create a spirit of mutual esteem, respect, and recognition among members consistent with the goals and mission of IPC.
IPC Focuses on Education and Onboarding
05/09/2024 | Andy Shaughnessy, Design007 MagazineI recently spoke with Carlos Plaza, senior director of education for IPC, about expanding educational efforts in the PCB design, fabrication, and assembly segments. As Carlos explains, PCB design is a hot topic, but onboarding may be the hottest one of all.
Real Time with… IPC APEX EXPO 2024: Industry Growth, Challenges, and Technological Advancements
05/09/2024 | Real Time with...IPC APEX EXPOEditor Nolan Johnson and Shawn DuBravac, IPC chief economist, dive into key industry topics such as growth, challenges, and technological advancements. They discuss shifts in the global competitive landscape, downstream demand, customization, and how AI is enhancing human skills. The industry outlook appears promising for both the short and long term.
Real Time with… IPC APEX EXPO 2024: The Driving World of e-Mobility with Indium
05/08/2024 | Real Time with...IPC APEX EXPOIn the competitive EV market, technology plays a crucial role facing the challenges of infrastructure. As Brian O'Leary explains, Indium's e-Mobility product suite includes proven solder and thermal management products for high reliability.
Real Time with… IPC APEX EXPO 2024: Understanding Objective Evidence in Manufacturing Processes
05/07/2024 | Real Time with...IPC APEX EXPOGraham Naisbitt explains the importance of objective evidence in manufacturing processes, debunking the common misconception that the ROSE test is a cleanliness test. He also discusses the introduction of Rev J, a requirement for measuring ionic contamination on circuit assemblies, and the challenges in accurately measuring contamination. Alternative methods like ion chromatography and the need for updating standards like the ROSE test are mentioned.