Sniffing Out the Foundational Science of Sensors
March 23, 2018 | U.S. Department of EnergyEstimated reading time: 9 minutes
The human nose can distinguish among a trillion different combinations of smells. Even so, there are plenty of gases that our noses can't detect at the level of sensitivity we need. That's where gaseous sensors come in. While some of the first sensors were animals – like canaries in coal mines – we've since replaced them with technologies that can detect miniscule amounts of chemicals in the air.
Image caption: This sensor can detect methane at much lower concentrations than current ones. It relies on nanotechnology developed at the Center for Nanoscale Materials, an Office of Science user facility.
Just like our own noses, gaseous sensors are essential for safety and comfort. In factories, gaseous sensors can alert managers to chemical leaks or processes running incorrectly. Outside, they measure pollutants, helping cities monitor air quality. In homes, they keep family members safe. Building managers use measurements from humidity and temperature sensors to maximize energy efficiency.
These sensors wouldn't exist without a fundamental understanding of chemistry and physics. This basic knowledge helps scientists understand how and why sensing materials interact with gaseous chemicals. Many cutting-edge materials have promise for use in sensors, if only scientists can learn how to better produce and control them.
"Sensors are where materials research meets environmental detection," said Pete Beckman, a researcher at Department of Energy's Argonne National Laboratory (ANL).
To set the groundwork for innovation, the DOE Office of Science funds projects and user facilities that support sensors research.
Creating the Materials for Sensing
Like noses, sensors rely on a combination of components to detect and make sense of gases or chemicals in the air. In humans, molecules float up into your nose and bind to special neurons. Neurons then pass the message up to the brain. In sensors, the material inside the sensor acts as a neuron. When that material interacts with a chemical in the air, it may emit light, change its ability to conduct electricity, or shift shape. The materials and electronics around the sensing material communicate that message to the sensor's "brain," whether that brain is a computer or a warning signal like a siren.
Developing sensors' nervous systems and brains is a job for applied science. Fundamental research like the work at the Office of Science's laboratories sets the foundation for that applied science. In particular, this research is expanding scientists' understanding of the materials themselves and how to produce them.
Three types of cutting-edge materials offer huge potential for use in sensors: nanoparticles, two-dimensional (2D) materials, and metal-organic frameworks (MOFs). Nanoparticles are miniscule particles that are bigger than atoms, but act fundamentally differently from larger particles of the same substance. 2D materials, like graphene, form sheets only a single atom thick. MOFs are compounds made of metal ions linked together by carbon-based connectors.
All of these materials have humongous surface areas compared to their overall sizes. Because lots of gas molecules can interact with their surfaces, they can be sensitive to tiny amounts of chemicals. In addition, scientists can craft all of these materials into a variety of structures. That customization could allow researchers to create specialty materials to detect a particular chemical.
Zinc Sulfide Nanoparticles
The key to building a better sensor may lie in making its sensing material out of nanoparticles. Unfortunately, it's challenging to manufacture some of the most promising of those nanoparticles. Sensors for hydrogen and other gases already use the material zinc sulfide. Producing zinc sulfide in nanoparticle form could make it cheaper and more effective. But the current process for producing zinc sulfide nanoparticles involves very high temperatures, pressures, and toxic chemicals.
Scientists at DOE's Oak Ridge National Laboratory (ORNL) investigated a cheaper, more efficient nanoparticle production process. Researchers supported by both DOE's Advanced Manufacturing Office and Office of Science found that microbes may offer an alternative path forwardExternal link.
Not just any bacteria will do. Scientists used Thermoanaerobacter, a bacteria that normally lives in extremely hot places with no oxygen. After adding a cheap sugar and chemicals that included zinc and sulfur, the bacteria produced about three-quarters of a pound of zinc sulfide nanoparticles. The process was 90 percent cheaper than current methods.
Page 1 of 3
Suggested Items
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources: