-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Making the Most of PCB Materials for 5G Microwave and mmWave Amps
June 13, 2018 | John Coonrod, Rogers CorporationEstimated reading time: 2 minutes
Millions of cell phones trying to connect voices and download unimaginable numbers of files worldwide point to the inevitability of fifth generation (5G) wireless communications networks. 5G is coming, and it will require the right circuit materials for many different types of high-frequency circuits, including power amplifiers (PAs). 5G represents the latest and greatest in wireless technology, and it will be challenging to design and fabricate, starting with the circuit board materials, because it will operate across many different frequencies, such as 6 GHz and below, as well as at millimeter-wave frequencies (typically 30 GHz and above). It will also combine network access from terrestrial base stations and orbiting satellites. But by careful consideration of mechanical and electrical requirements, high-frequency circuit materials can be specified that enable the design and development of 5G PAs no matter the frequency.
Ideally, a single circuit material would be a suitable starting point for PAs at all frequencies. However, amplifiers at different frequencies have different design requirements and are best supported by circuit materials with different characteristics best suited to the different frequencies. For example, insertion loss or dissipation factor can be more or less depending on the type of circuit material. Every circuit material will suffer some amount of loss, which typically increases with increasing frequency. The loss performance of a given circuit material may be acceptable within the microwave frequencies to be used in 5G networks but not within the millimeter-wave frequency range, where signal power tends to be less with increasing frequencies. The circuit material that provides the low loss needed for high PA gain and output power at microwave frequencies may not be the best choice of material for a PA at millimeter-wave frequencies.
The design requirements for a key circuit material parameter, dielectric constant (Dk), are much different for microwave frequencies, such as the 6 GHz and below used with 5G systems, than for millimeter-wave frequencies, such as 30 GHz and above, as will be used for short-range backhaul links in 5G wireless networks. Selecting an optimum circuit material for each band of frequencies requires understanding which Dk value best supports each of the two different frequency ranges. Then it is a matter of finding circuit materials that possess those Dk values along with as many as possible of the other circuit material attributes that help make a good, high-performance, high-frequency PA.
To read this entire article, which appeared in the May 2018 issue of Design007 Magazine, click here.
Suggested Items
Elementary, Mr. Watson: Ensuring Design Integrity
03/28/2024 | John Watson -- Column: Elementary, Mr. WatsonBack in February, many of us watched the "Big Game." It reminded me of the saying, “It's not how you start that is important, but rather how you finish." It is perfectly okay when you are talking about sports, you get off to a bad first half and need to recover in the second half. However, when it comes to PCB design, this is not a good practice. If things start badly, they usually don't recover. They continue down that same path, costing more money and losing design time.
Arrow Electronics Launches Intelligent Vision Ecosystem
03/27/2024 | BUSINESS WIREArrow Electronics, Inc. is utilizing the onsemi Imager Access System (IAS) module standard for developing intelligent vision solutions for use in robotics, machine vision, commercial cameras and other uses.
Dymax Will Exhibit Light-Cure Solutions for Today’s Electronics at IPC APEX 2024
03/26/2024 | DymaxDymax, a leading manufacturer of rapid and light-curing materials and equipment, will exhibit at the IPC APEX EXPO 2024 in Anaheim, CA, April 9-11.
Synopsys Announces New AI-Driven EDA, IP and Systems Design Solutions At SNUG Silicon Valley
03/25/2024 | PRNewswireSynopsys, Inc. kicked off its annual flagship Synopsys User Group (SNUG) conference in Silicon Valley at the Santa Clara Convention Center with a keynote presentation by Synopsys president and CEO Sassine Ghazi. Ghazi discussed the unprecedented innovation opportunities and challenges that technology R&D teams face in this era of pervasive intelligence.
New North American Product Family Release from Smart Factory Design
03/22/2024 | Smart Factory DesignSmart Factory Design is pleased to announce a new system technology and supply chain model for providing Zero Liquid Discharge (ZLD) Wastewater Recycling Systems to the North American market. Smart Factory Design is an international public benefit company focused on environmental sustainability and autonomous processes for the Printed Circuit Board, IC Substrate, and General Metal Finishing industries.