Generating Electrical Power from Waste Heat
July 10, 2018 | Sandia National LaboratoriesEstimated reading time: 5 minutes
Directly converting electrical power to heat is easy. It regularly happens in your toaster, that is, if you make toast regularly. The opposite, converting heat into electrical power, isn’t so easy. Researchers from Sandia National Laboratories have developed a tiny silicon-based device that can harness what was previously called waste heat and turn it into DC power.
Image caption: This tiny silicon-based device developed at Sandia National Laboratories can catch and convert waste heat into electrical power. The rectenna, short for rectifying antenna, is made of common aluminum, silicon and silicon dioxide using standard processes from the integrated circuit industry. (Photo by Randy Montoya) Click on the thumbnail for a high-resolution image.
“We have developed a new method for essentially recovering energy from waste heat. Car engines produce a lot of heat and that heat is just waste, right? So imagine if you could convert that engine heat into electrical power for a hybrid car. This is the first step in that direction, but much more work needs to be done,” said Paul Davids, a physicist and the principal investigator for the study.
“In the short term we’re looking to make a compact infrared power supply, perhaps to replace radioisotope thermoelectric generators.” Called RTGs, the generators are used for such tasks as powering sensors for space missions that don’t get enough direct sunlight to power solar panels.
Davids’ device is made of common and abundant materials, such as aluminum, silicon and silicon dioxide — or glass — combined in very uncommon ways.
Silicon device catches, channels and converts heat into power
Smaller than a pinkie nail, the device is about 1/8 inch by 1/8 inch, half as thick as a dime and metallically shiny. The top is aluminum that is etched with stripes roughly 20 times smaller than the width of a human hair. This pattern, though far too small to be seen by eye, serves as an antenna to catch the infrared radiation.
Between the aluminum top and the silicon bottom is a very thin layer of silicon dioxide. This layer is about 20 silicon atoms thick, or 16,000 times thinner than a human hair. The patterned and etched aluminum antenna channels the infrared radiation into this thin layer.
The infrared radiation trapped in the silicon dioxide creates very fast electrical oscillations, about 50 trillion times a second. This pushes electrons back and forth between the aluminum and the silicon in an asymmetric manner. This process, called rectification, generates net DC electrical current.
The team calls its device an infrared rectenna, a portmanteau of rectifying antenna. It is a solid-state device with no moving parts to jam, bend or break, and doesn’t have to directly touch the heat source, which can cause thermal stress.
Infrared rectenna production uses common, scalable processes
Because the team makes the infrared rectenna with the same processes used by the integrated circuit industry, it’s readily scalable, said Joshua Shank, electrical engineer and the paper’s first author, who tested the devices and modeled the underlying physics while he was a Sandia postdoctoral fellow.
He added, “We’ve deliberately focused on common materials and processes that are scalable. In theory, any commercial integrated circuit fabrication facility could make these rectennas.”
That isn’t to say creating the current device was easy. Rob Jarecki, the fabrication engineer who led process development, said, “There’s immense complexity under the hood and the devices require all kinds of processing tricks to build them.”
One of the biggest fabrication challenges was inserting small amounts of other elements into the silicon, or doping it, so that it would reflect infrared light like a metal, said Jarecki. “Typically you don’t dope silicon to death, you don’t try to turn it into a metal, because you have metals for that. In this case we needed it doped as much as possible without wrecking the material.”
The devices were made at Sandia’s Microsystems Engineering, Science and Applications Complex. The team has been issued a patent for the infrared rectenna and have filed several additional patents.
The version of the infrared rectenna the team reported in Physical Review Applied produces 8 nanowatts of power per square centimeter from a specialized heat lamp at 840 degrees. For context, a typical solar-powered calculator uses about 5 microwatts, so they would need a sheet of infrared rectennas slightly larger than a standard piece of paper to power a calculator. So, the team has many ideas for future improvements to make the infrared rectenna more efficient.
Future work to improve infrared rectenna efficiency
These ideas include making the rectenna’s top pattern 2D x’s instead of 1D stripes, in order to absorb infrared light over all polarizations; redesigning the rectifying layer to be a full-wave rectifier instead of the current half-wave rectifier; and making the infrared rectenna on a thinner silicon wafer to minimize power loss due to resistance.
Through improved design and greater conversion efficiency, the power output per unit area will increase. Davids thinks that within five years, the infrared rectenna may be a good alternative to RTGs for compact power supplies.
Shank said, “We need to continue to improve in order to be comparable to RTGs, but the rectennas will be useful for any application where you need something to work reliably for a long time and where you can’t go in and just change the battery. However, we’re not going to be an alternative for solar panels as a source of grid-scale power, at least not in the near term.”
Davids added, “We’ve been whittling away at the problem and now we’re beginning to get to the point where we’re seeing relatively large gains in power conversion, and I think that there’s a path forward as an alternative to thermoelectrics. It feels good to get to this point. It would be great if we could scale it up and change the world.”
The research was funded by Sandia’s Laboratory Directed Research and Development program.
About Sandia National Laboratories
Sandia National Laboratories is a multimission laboratory operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration. Sandia Labs has major research and development responsibilities in nuclear deterrence, global security, defense, energy technologies and economic competitiveness, with main facilities in Albuquerque, New Mexico, and Livermore, California.
Suggested Items
Apollo Seiko Presents the Next Frontier in Non-Contact Soldering at 2024 IPC APEX EXPO
03/12/2024 | Apollo SeikoApollo Seiko, a leading innovator in soldering technology, is pleased to announce plans to showcase its latest advancements at Booth 1408 during the 2024 IPC APEX EXPO, taking place April 9-11, 2024 at the Anaheim Convention Center in California.
Indium Corporation Experts to Present at SEMI THERM
03/07/2024 | Indium CorporationIndium Corporation Global Account Manager and Senior Thermal Technologist Tim Jensen and Product Development Specialist for Thermal Interface Materials Miloš Lazić will present on thermal interface material (TIM) technology at SEMI-THERM, taking place March 25–28 in San Jose, California, U.S.
CE3S Offers PACE’s ADS200 AccuDrive Soldering Station with TD-200 & 3 Tip Bundle
03/04/2024 | CE3SCumberland Electronics Strategic Supply Solutions (CE3S), a leading provider of quality goods and services, is pleased to offer PACE's ADS200 AccuDrive Soldering Station. Designed for serious cell-phone repairers, electronics techs, engineers, DIYers, and production solder techs, the ADS200 is a high-power yet cost-effective soldering solution that delivers world-class performance and reliability.
Exploring Cold Milling as an Alternative PCB Component Removal Method
01/24/2024 | Bob Wettermann, BEST Inc.When a PCB undergoes multiple heat cycles, inherent risks emerge, primarily due to the expansion and contraction of materials. This thermal stress can induce various issues, including delamination, warping, compromised solder joints, and damage to heat-sensitive components like integrated circuits or capacitors.
Register Now for the IPC Design Competition 2024
12/19/2023 | IPC StaffEvery year, thousands of printed board design engineers spend countless hours completing and perfecting their designs. IPC is inviting these designers to put their skills to the test and compete to become the IPC Design Champion of 2024. As in previous years, the IPC Design Competition is composed of two parts: a Virtual Heat and a Finals Heat. Each heat features a board design created especially for this competition by IPC instructor Kris Moyer.