-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
3D Convergence of Multiboard PCB and IC Packaging Design
July 18, 2018 | Bob Potock, ZukenEstimated reading time: 3 minutes
The electronic product design process is being challenged like never before, with the need to develop feature-rich, light, compact products at a lower cost, in less time. To address these challenges, designers are combining chips and boards in new configurations, such as complex 3D stacked structures, or new packaging technologies like package-on-package (PoP) and system-in-package (SiP). They are also embedding passive and active components on inner layers, inside cavities and within the dielectric of the board stack-up.
Traditional 2D PCB design systems are used to design one PCB at a time in isolation from the other PCBs within a product, and also in isolation from the ICs, packages, and enclosure. Validating connections between the PCBs, collision checking the boards to the enclosure, and reducing interconnection distance to the ICs requires time-consuming manual operations that are error-prone and limit the potential for reuse.
A new generation of 3D multiboard product-level design tools offer major improvements by managing multiboard placement in both 2D and 3D, and enabling co-design of the chip, package and board in a single environment. Multiboard design makes it possible to create and validate a design with any combination of system-on-chips (SOCs), packages, and PCBs as a complete system. Chip-package-board co-design enables designers to optimize routability via pin assignment and I/O placement to minimize layer counts between the package, chip and board. The new design methodology makes it possible to deliver more functional, higher performing and less expensive products to market in less time.
Multiboard Design Challenges
Today’s complex multiboard electronic products create design challenges, such as planning and management of interconnects at the system level. In current-generation tools, the signal verification process for a multiboard design involves exporting pin lists that include net names for each board connector and correlating the net names to the master list of net names. In many cases, it’s also necessary to manually verify each board connector’s signal name. With mechanical engineers and board designers working with disconnected systems it’s difficult, if not impossible, to intelligently manage connectivity and changes between boards. Using a spreadsheet or some other disconnected document to manage the large number of interconnects between the PCBs in the system is time-consuming and prone to error.
When mechanical engineers have inaccurate information on the electrical design or electrical engineers have inaccurate information on the mechanical design, the result in many cases is that batteries don’t fit, mounting screws create shorts against PCBs, and connectors don’t mate with packaging openings. Improper management can easily result in wasted product development time, scrapped boards and slipped schedules.
The combination of increasing capabilities, shrinking size and more complex external shapes means that electronics must increasingly consider the shape of the package while the mechanical design is more dependent than ever on the physical aspects of the internal electronics. Multi-board designs make ECAD-to-MCAD translation more difficult because of the need to communicate the position of connectors and other common points between the boards.
Yet in the current generation of tools, the collision-checking process involves exporting placement information, usually in IDF format, for each PCB to a mechanical engineer for assembly analysis. PCB design tools have continued to focus on working in 2D on one PCB at a time, with the electrical work done in 2D and then the 2D design being exported into 3D mechanical design software where the boards are positioned and checked for interference. The PCB designer is unable to, for example, position two boards on top of each other to see how they fit together. This is normally done after the board design has been exported to the mechanical design tool. Interdependencies between interlocking boards and their enclo-sure in complex products are critical.
To read this entire article, which appeared in the June 2018 issue of Design007 Magazine, click here.
Suggested Items
Cadence, TSMC Collaborate on Wide-Ranging Innovations to Transform System and Semiconductor Design
04/25/2024 | Cadence Design SystemsCadence Design Systems, Inc. and TSMC have extended their longstanding collaboration by announcing a broad range of innovative technology advancements to accelerate design, including developments ranging from 3D-IC and advanced process nodes to design IP and photonics.
Ansys, TSMC Enable a Multiphysics Platform for Optics and Photonics, Addressing Needs of AI, HPC Silicon Systems
04/25/2024 | PRNewswireAnsys announced a collaboration with TSMC on multiphysics software for TSMC's Compact Universal Photonic Engines (COUPE). COUPE is a cutting-edge Silicon Photonics (SiPh) integration system and Co-Packaged Optics platform that mitigates coupling loss while significantly accelerating chip-to-chip and machine-to-machine communication.
Siemens’ Breakthrough Veloce CS Transforms Emulation and Prototyping with Three Novel Products
04/24/2024 | Siemens Digital Industries SoftwareSiemens Digital Industries Software launched the Veloce™ CS hardware-assisted verification and validation system. In a first for the EDA (Electronic Design Automation) industry, Veloce CS incorporates hardware emulation, enterprise prototyping and software prototyping and is built on two highly advanced integrated circuits (ICs) – Siemens’ new, purpose-built Crystal accelerator chip for emulation and the AMD Versal™ Premium VP1902 FPGA adaptive SoC (System-on-a-chip) for enterprise and software prototyping.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
IPC Design Competition Champion Crowned at IPC APEX EXPO 2024
04/24/2024 | IPCAt IPC APEX EXPO 2024 in Anaheim, California, five competitors squared off to determine who was the best of the best at PCB design.