PCB Design, Fabrication and Use from the Mil-Aero End-User Perspective
August 28, 2018 | Pete Starkey, I-Connect007Estimated reading time: 13 minutes
How do leading military and aerospace electronics end-users define their high-reliability printed circuit board requirements? How do they specify their materials? What factors determine their design rules? How do they deal with impedance control? What are their preferred solderable finishes? How do they qualify a new design? And when PCBs are delivered, what are their incoming inspection and quality standards, and how are the boards tested? How are PCBs handled and what precautions are taken to control moisture absorption?
The answers to these and many more questions were provided by a webinar organised by the European chapter of SMTA, moderated by Bob Willis and presented by two industry experts with whom I had the privilege of working for many years on the SMART Group technical committee and latterly as members of the SMTA Europe technical committee: Charles Cawthorne, industrial electronics technologist with MBDA Systems, and Ian Fox, electronics materials and process specialist with Rolls Royce. Their input exemplified the standards and practices adopted by a manufacturer of missile systems and a manufacturer of aero-engine controls and characterised the typical requirements of the hi-rel mil-aero sector.
The first part of the webinar was delivered by Charles Cawthorne, who reviewed the basic fabrication steps for a sequential-build 10-layer PCB as an introduction to a discussion of laminates, prepregs, copper foils and flex-rigid materials, and various aspects of design including via protection and controlled impedance.
The defining specification for base materials for rigid and multilayer printed circuit boards was IPC-4101, with its associated slash sheets defining resin and reinforcement systems, testing parameters and properties. Cawthorne quoted examples of FR-4 materials that demonstrated different glass transition temperatures (Tg), the baseline being IPC-4101/21 with a 110°C minimum Tg. In fact, MBDA specified IPC-4101/126, with a 170°C minimum Tg. But was it sufficient simply to define a Tg? Cawthorne stressed the importance of considering Z-axis coefficient of thermal expansion (CTE), especially above Tg, and explained that MBDA required a Z-axis TCE of less than 60ppm/°C below Tg and less than 300ppm/°C above Tg. Additionally, MBDA required a decomposition temperature (Td) no less than 325°C and a time to delamination at 260°C (T260) of no less than 30 minutes.
For operating temperature above about 130°C, polyimide materials were preferred, example grades being IPC-4101/40, with Tg of 200°C minimum, and IPC-4101/41 with Tg of 250°C minimum, but these materials were significantly more expensive than FR-4.
The defining standard for copper foils was IPC-4562. Cawthorne explained the meaning of the full specification sheet designation, taking as example a typical foil used by MBDA for outer layers: IPC-4562A/3 CuE3HSXS3, where /3 was the IPC-4562 Spec Sheet Number, Cu denoted copper, E indicated electrodeposited, 3 signified high temperature elongation, H indicated half-ounce thickness, S stood for single-sided bond enhancement, XS indicating that this was standard profile, and the final 3 referred to highest quality.
For the additional materials required for flex-rigid multilayer constructions, no flow prepreg was defined by IPC-4101/40, 41 or 42, flex cores by IPC-4204, and coverlays and bond-plies by IPC-4203. MBDA typically used polyimide-based adhesiveless flex cores in accordance with IPC-4204/11.
Cawthorne moved on to a discussion of surface mount design rules, beginning with component footprints for which the defining standard was IPC-7351. This considered three density levels, where Level A represented the largest footprint and Level C the smallest. MBDA used a software-based footprint calculator to optimise design for manufacture, and generally chose to work at Density Level B to give the best compromise between ease of manufacture and minimum footprint area.
The defining standards for PCB layout were the generic IPC-2221 and the sectional standards IPC-2222, IPC-2223 and IPC-2226. There had been lengthy discussion on the relative merits of solder-mask-defined or non-solder-mask-defined BGA pads, and MBDA considered the latter a more reliable option. Concerning offset vias, their preference was to ensure that solder resist was present between BGA pad and via to prevent wicking of solder away from the joint.
The defining standard for PTH footprints was IPC-7251, which covered three density levels, Level A being for the largest hole diameter and Level C the smallest. Historically, MBDA had used Level B or Level C for tin-lead but experience had shown that the PTH diameter needed to be increased for lead-free and Level A had now been adopted for both tin-lead and lead-free soldering. Standard maximum aspect ratio for plated-through holes was 6:1 for rigid boards and 5:1 for flex-rigid. For buried vias, minimum aspect ratios were 7:1 for rigid boards and 6:1 for flex-rigid, with minimum diameter 0.25 mm depending on current handling requirements.
Page 1 of 3
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.