Could a DIY Ultrasound be in Your Future?
September 12, 2018 | University of British ColumbiaEstimated reading time: 1 minute
Engineers at the University of British Columbia have developed a new ultrasound transducer, or probe, that could dramatically lower the cost of ultrasound scanners to as little as $100. Their patent-pending innovation—no bigger than a Band-Aid—is portable, wearable and can be powered by a smartphone.
Conventional ultrasound scanners use piezoelectric crystals to create images of the inside of the body and send them to a computer to create sonograms. Researchers replaced the piezoelectric crystals with tiny vibrating drums made of polymer resin, called polyCMUTs (polymer capacitive micro-machined ultrasound transducers), which are cheaper to manufacture.
“Transducer drums have typically been made out of rigid silicon materials that require costly, environment-controlled manufacturing processes, and this has hampered their use in ultrasound,” said study lead author Carlos Gerardo, a PhD candidate in electrical and computer engineering at UBC. “By using polymer resin, we were able to produce polyCMUTs in fewer fabrication steps, using a minimum amount of equipment, resulting in significant cost savings.”
Sonograms produced by the UBC device were as sharp as or even more detailed than traditional sonograms produced by piezoelectric transducers, said co-author Edmond Cretu, professor of electrical and computer engineering.
“Since our transducer needs just 10 volts to operate, it can be powered by a smartphone, making it suitable for use in remote or low-power locations,” he added. “And unlike rigid ultrasound probes, our transducer has the potential to be built into a flexible material that can be wrapped around the body for easier scanning and more detailed views–without dramatically increasing costs.”
Co-author Robert Rohling, also a professor of electrical and computer engineering, said the next step in the research is to develop a wide range of prototypes and eventually test their device in clinical applications.
“You could miniaturize these transducers and use them to look inside your arteries and veins. You could stick them on your chest and do live continuous monitoring of your heart in your daily life. It opens up so many different possibilities,” said Rohling.
Suggested Items
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
02/23/2024 | Andy Shaughnessy, Design007 MagazineIt was a good week in PCB design and manufacturing. In this week’s wrap-up, we have news about an uptick in EMS shipments in January, a look at the current M&A climate, some guidance on investing in your company in order to stay competitive, a primer on designing with embedded capacitance materials, and a roadmap for the industry to embrace sustainable PCBs in the future.
Every Designer Needs to Understand Embedded
02/14/2024 | I-Connect007 Editorial TeamIPC’s Kris Moyer teaches design techniques for embedding components, and he’s noticed an upswing in his students’ interest in embedded component design. We recently spoke with him about embedding component design: best practices, pros and cons, and when it makes sense for designers to start embedding.
IPC Standards: Ticket to a Safe Passage
10/26/2023 | I-Connect007 Editorial TeamJohn Watson, CID, is a customer success manager with Altium who also teaches PCB design at Palomar College in Carlsbad, California. He’s noticed that most of his students are primarily new to the industry and not familiar with IPC standards. In his classes, he teaches how to use these standards while trying to help students access the documents more easily. When we met with John, we asked him to discuss the importance of understanding IPC standards, the price you’ll pay if you decide not to follow them, and his plans for getting new designers on board with standards as early as possible in their careers.
PCBflow Fosters Collaboration Between Design and Manufacture
10/23/2023 | Andy Shaughnessy, Design007 MagazineDuring PCB West, I spoke with Susan Kayesar, program manager for PCBflow, a business unit of Siemens that provides a collaboration environment for designers and manufacturers. We discussed the intent behind PCBFlow and how this platform helps to improve pre-manufacture communications.
Connect the Dots: Best Practices for Prototyping
09/21/2023 | Matt Stevenson -- Column: Connect the DotsPCB prototyping is a critical juncture during an electronic device’s journey from concept to reality. Regardless of a project’s complexity, the process of transforming a design into a working board is often enlightening in terms of how a design can be improved before a PCB is ready for full production.