Substrates for Advanced PCB Technologies: What Will the Future Hold?


Reading time ( words)

The UK chapter of the global IMAPS community of electronics and microelectronic packaging engineers shared a wealth of knowledge and wisdom about PCB substrate technology trends, developments, and future requirements in a webinar on the first of November. The webinar was introduced on behalf of IMAPS-UK by National Physical Laboratory’s electronics interconnection expert Martin Wickham and featured presentations by Piers Tremlett and Jim Francey.

Martin_Wickham.jpg“Who knows which future substrate will be successful?” Aware of a need to exercise caution when attempting predictions, Piers Tremlett, engineering specialist at Microsemi, quoted an example from ancient Greece: “The Oracle at Delphi knew how to error-proof her future predictions. Everyone else gets it wrong; it’s just a question of by how much.” Nevertheless, his presentation painted a very clear picture of the future for printed circuit substrates, even exploring the possibilities for “substrateless” circuits.

Driven by a need to satisfy the desires of users, substrate technology aimed to improve performance and eliminate waste whilst minimising cost. Tremlett discussed the fluidity of future circuit structures, the potential growth of flexible substrates, the rise in substrates for handling power and heat, and trends from two-dimensional to three-dimensional circuit assemblies. He focused on four relevant topics: miniaturisation for mobile products, heat and power, printed electronics, and substrateless circuits.

Piers_Tremlett.jpgMobile products, especially smartphones, and the cost savings of using less material were the primary drivers for miniaturisation. As an example, Tremlett showed a cross-section of an iPhone 7 with a coreless 10-layer 500-micron substrate and sub-20-micron tracks densely populated with components and a lot of interconnect in a very small space. The interconnect was realised by semi-additive processing, pattern plating on a very thin base copper, and flash etching. As laser direct imaging capability improved and track widths trended towards 10 microns, it was preferred to embed them into the substrate surface to improve reliability, as demonstrated by the Daisho Denshi ultra-narrow pitch flush pad interposer. In his iPhone 7 example, the memory chip was mounted on a very thin three-layer PCB, underneath which was the processor chip with no substrate as such—all the tracks were laid on the packaging material itself and had produced significant performance improvements. He commented that fan-out wafer-level packaging was moving from silicon wafer technology to PCB technology with more than one component inside the mould compound, which could be seen as a paradigm shift away from FR-4 and surface mount.

Conventional assembly technology was giving way to embedded die technology and ultra-thin chip technology, leading to smaller and thinner devices. But whereas the trend had always been to push components off the PCB and on to the silicon, this was now becoming a more expensive option, and the components were being pushed back up into the packaging fab to continue the drive towards integration. Packaging was moving towards complete subsystems, placing more emphasis on substrate capability in terms of layer count and track width and presenting considerable competition to conventional PCB concepts.

Tremlett turned his attention to thermal management, increasing heat being generated by faster processors, RF chips, power chips and LEDs. It was becoming less practicable to use ceramic substrates except for special applications because of considerations of cost, small panel geometries, and high-temperature processing. So, could organic substrates be used as alternatives? He discussed thermal via designs, several forms of integrated metal substrates, metal inserts, and even water-cooled PCBs, and compared their efficiencies as a means of heat dissipation. He reviewed innovations in chip embedding for power packaging that had proven benefits for low- and high-power analogue and digital and RF products and described proprietary embedding package solutions such as SESUB and aEASI. The EmPower project was an international consortium developing embedded power semiconductors for the drive electronics in electric vehicle applications in a module that enabled heat removal on both sides over the shortest possible heat conduction paths.

Share

Print


Suggested Items

Alun Morgan on Thermal Management and LEDs in Automotive

04/25/2019 | Judy Warner
Guest Editor Judy Warner met with Alun Morgan, technology ambassador for Ventec International Group, to discuss topics addressed at the Automotive Executive Forum that took place at IPC APEX EXPO 2019. Morgan describes his presentation and findings centered around thermal management in automotive, specifically LEDs, as well as the unique set of growing thermal management challenges Tier 1 suppliers are now facing in the automotive sector.

Stacked Microvia Reliability: Ongoing Work and Upcoming IPC Conference

04/24/2019 | Pete Starkey, I-Connect007
One year ago, Happy Holden's review of the 2018 IPC High-Reliability Forum reported the presentation of J.R. Strickland and Jerry Magera, who described research at MSI Applied Technology into overcoming the risk of stacked microvia failures escaping standard quality assurance procedures. Their report provided a basis for the IPC white paper IPC-WP-023, which addressed reliability issues associated with stacked microvias and included data collected from several other printed circuit manufacturers.

ITEQ’s Tarun Amla Discusses 5G Inflection Points

04/08/2019 | Andy Shaughnessy, I-Connect007
ITEQ Corporation Executive VP and CTO Tarun Amla discusses effects of 5G on materials and shares general observations on the 5G rollout at DesignCon. He also talks about the challenges for their customers, and how they help them address their issues.



Copyright © 2019 I-Connect007. All rights reserved.