-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Communication, Part 5: Internet Impedance Calculators for Modeling
November 5, 2019 | Steve Williams, The Right Approach Consulting LLCEstimated reading time: 4 minutes
Bob Chandler of CA Design and Mark Thompson of Prototron Circuits address how new engineers use internet impedance calculators for modeling (e.g., formulas versus recipes) in Part 5 of this series.
Steve Williams: Today, we want to talk today about a phenomenon that I wasn’t personally aware of until Mark brought it to my attention, which surrounds engineers going on the internet, searching for impedance modeling calculators, and using that to come up with their impedance calculations. Bob, what do you think about that?
Bob Chandler: It is definitely happening. I like to talk to about it as formulas versus recipes, and engineers love to deal with formulas, where they key in the numbers and come up with the solution. They’re not used to dealing with recipes, where you take the basic ingredients, and depending on how you process those, come up with totally different products. Once, the same board with the same data was manufactured at two different fab houses and had completely different controlled impedances, even though the trace widths, materials, etc., were identical. One shop fabricated it at a slightly different temperature and pressure than the other one, which resulted in a completely different controlled impedance. So, talk to your fabricator because the process has as much impact on the controlled impedance as the material and trace width do.
Williams: We’ve talked in the past about some designers just throwing out boilerplate notes and requirements on drawings. This sounds like the same thing, but there are a lot more consequences if that happens.
Mark Thompson: Absolutely. And Bob brings up a great point. Even if you have the same stackup of the same material and the same trace and space sizes, because of different press parameters and environmental conditions, all kinds of other factors can combine to make deviations in those impedances. And that’s where the conversation between the designer and the fabrication house takes place.
First, I see that some folks use online calculators, like those provided by the Missouri University of Science & Technology [formerly the University of Missouri-Rolla]. However, if you look at it and the Z-axis shape of the trace, it has vertical walls; it’s a rectangular slab. There is no etchant in the world that works perfectly with 90° corners. Second, calculations are frequently made without any solder mask or polymer mask plastic over the top of the traces, which will also affect the impedances. Third, sometimes, a wrong dielectric constant is used.
Williams: How should companies do their modeling? Should it be based on experience, software, or working with the design bureau?
Thompson: The best way to do it is, as Bob said, is to start with a conversation between the engineer and designer and agree on the material, copper weight, color of the solder mask, whether or not there will be free space structures, and whether or not there will be coplanar structures. Beyond that, I can provide that information, and include all the effective dielectric contents of all of the subsections based on Prototron Circuits.
Chandler: The main thing is to go back to the fabrication house and ask them what they would prefer. Because if you design your board was a certain setup, and then you send it to the fabrication house for a three-day turn, and they can’t manipulate the numbers, your three-day turn turns into a one week and three-day turn, as they have to special order materials.
Williams: That’s a great point.
Thompson: And in today’s world, where people are designing with 0.1-millimeter lines and spaces, any deviation where I have to increase or decrease that trace or space may throw us out of the game and make it not producible for a fabrication house. Nothing ruins a designer’s day more than having a fabrication house calling and saying, “I’m sorry, but we can’t get there from here.”
Williams: Out of all the business that you do, Mark, how much of it requires controlled impedance and modeling?
Thompson: That’s a great question. When I started here 23 years ago, I brought controlled impedance on board; we didn’t do any—only four and six layers. We started out with four- and six-layer impedances, very simple stripline constructions and dual asymmetrics, some at 50 ohms, others at 100 ohms, etc.. Now, over 70% of all the jobs that come through Prototron today are signal integrity.
Williams: So, it’s a big deal.
Thompson: Yes.
Williams: Bob, how does that match up to your designs as far as how many have controlled impedance and people’s requirements?
Chandler: It’s very similar, probably 70–80%, depending on our current customer base. Some of our customers have many more requirements for it, and others are much less requirement-driven.
Williams: It sounds like you and Bob are on the same page, at least.
Thompson: Without a doubt.
Editor’s note: Read Part 1, Part 2, Part 3, and Part 4, and stay tuned for the final installment of this series.
Steve Williams is the president of The Right Approach Consulting and an I-Connect007 columnist.
Bob Chandler is CTO of CA Design (cadesign.net) and a senior Allegro/OrCAD trainer and consultant.
Mark Thompson, CID+, is in engineering support at Prototron Circuits and an I-Connect007 columnist. Thompson is also the author of The Printed Circuit Designer's Guide to… Producing the Perfect Data Package. Visit I-007eBooks.com to download this book and other free, educational titles.
Suggested Items
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.
Empowering Electronics Assembly: Introducing ALPHA Innolot MXE Alloy
04/16/2024 | MacDermid Alpha Electronics SolutionsIn the rapidly evolving electronics industry, where innovation drives progress, MacDermid Alpha Electronics Solutions is committed to setting a new standard. Today, we are pleased to introduce ALPHA Innolot MXE, a revolutionary alloy meticulously engineered to address the critical needs of enhanced reliability and performance in modern electronic assemblies.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
Inkjet Solder Mask ‘Has Arrived’
04/10/2024 | Pete Starkey, I-Connect007I was delighted to be invited to attend an interactive webinar entitled “Solder Mask Coating Made Easy with Additive Manufacturing,” hosted by SUSS MicroTec Netherlands in Eindhoven. The webinar was introduced and moderated by André Bodegom, managing director at Adeon Technologies, and the speakers were Mariana Van Dam, senior product manager PCB imaging solutions at AGFA in Belgium; Ashley Steers, sales manager at Electra Polymers in the UK; and Dr. Luca Gautero, product manager at SUSS MicroTec Netherlands.