Reliability Assessment of No-clean and Water-soluble Solder Pastes, Part II


Reading time ( words)

Note: Part 1 of this article published in the March 2014 issue of SMT Magazine, available here.

Twenty-five years ago, solder paste residues had to be cleaned after reflow due to their corrosive nature: two ways of cleaning were available, either with solvent or by using water, with or without detergent. Now, the assembly world is mainly no-clean: paste formulation is safer in terms of chemical reliability and process costs are reduced without cleaning. However, some applications (i.e., military, aerospace, high-frequency, and semiconductor) require a perfect elimination of the residue after reflow. Several options can achieve this result: a no-clean paste which allows residue to be removed with the most suitable cleaning method, or a paste designed to be cleaned, such as a water-soluble solder paste.

Water-soluble solder pastes generally show great wettability because of their strong activation but they are also known to have shorter stencil life and to be more sensitive to working conditions as temperature and humidity, compared to the no-clean pastes. Additionally, with the components stand-off getting smaller and smaller, washing residues with water only is more and more challenging due to its high surface tension: the addition of detergent becomes often necessary.

The purpose of this article is to highlight the differences between these two families of solder pastes to guide users in their choice. This will be achieved through the comparison of several recent water-soluble and no-clean formulations as far as reliability is concerned. First, the printing quality will be evaluated (viscosity, tack, cold slump, printing speed according to pressure, stencil life, idle time, printing consistency). Next, the reflow properties will be compared (hot slump, solderballing, reflow process window, wetting ability on different finishes).

Finally, the residue cleanability will be assessed. The IPC SIR will be also done to conclude the study. Both standardized tests and production tests will be used to evaluate the performance of these two kinds of solder pastes.

Introduction

Six lead-free pastes were extensively studied, three being water-soluble and three being no-clean. The first part of the study focused on printing performance. The pastes were characterized using standardized tests and internally developed tests: dynamic viscosity, tackiness, slump and solderballing. The influence of accelerated storage at elevated temperature, the influence of time and conditions between printing and reflow and the influence of continuous shear according to time were shown. The printing performances were also evaluated in a printer. Although the number of pastes studied was restricted, the water- soluble pastes generally yielded results below the no-clean pastes with more sensitivity to temperature and humidity, tendency to slump during preheat and narrower printing window. Water- soluble solder pastes must be stored, handled and used with more caution before reflow.

In the second part of the paper, the reflow properties will be compared: wettability, reflow process window, anti-graping properties. Finally the residue cleanability with water, then with water and detergents will be examined. The cleanliness will be assessed using visual inspection, ionic contamination and surface insulation resistance tests.

Read The Full Article Here

Editor's Note: This article originally appeared in the April issue of SMT Magazine.


Share

Print


Suggested Items

Top 10 Most-Read SMT Articles of 2020

12/31/2020 | I-Connect007
As 2020 comes to a close, the I-Connect007 Editorial Team takes a look back at its most read articles. Here are the top 10 reads in SMT from the past year.

Meet Christine Davis, I-Connect007 Columnist

12/23/2020 | I-Connect007 Editorial Team
Meet Christine Davis, one of our newest columnists! Christine will share her expertise and lessons learned through her journey as one of the few women in the electronics industry to found and run her own company.

Book Excerpt: The Printed Circuit Assembler’s Guide to Smart Data

12/16/2020 | Sagi Reuven and Zac Elliott, Siemens Digital Industries Software
Whenever we discuss data, keep in mind that people have been collecting data, verifying it, and translating it into reports for a long time. And if data is collected and processes are changed automatically, people still will be interpreting and verifying the accuracy of the data, creating reports, making recommendations, solving problems, tweaking, improving, and innovating. Whatever data collection system is used, any effort to digitalize needs to engage and empower the production team at the factory. Their role is to attend to the manufacturing process but also to act as the front line of communications and control.



Copyright © 2021 I-Connect007. All rights reserved.