Beyond Design: Stackup Planning, Part 3


Reading time ( words)

Following on from the first Stackup Planning columns, this month’s Part 3 will look at higher layer-count stackups. The four- and six-layer configurations are not the best choice for high-speed design. In particular, each signal layer should be adjacent to, and closely coupled to, an uninterrupted reference plane, which creates a clear return path and eliminates broadside crosstalk. As the layer count increases, these rules become easier to implement but decisions regarding return current paths become more challenging.

Given the luxury of more layers:

  • Electromagnetic compliancy (EMC) can be improved or more routing layers can be added.
  • Power and ground planes can be closely coupled to add planar capacitance, which is essential for GHz plus design.
  • The power distribution networks (PDNs) can be improved by substituting embedded capacitance material (ECM) for the planes.
  • Multiple power planes/pours can be defined to accommodate the high number of supplies required by today’s processors and FPGAs.
  • Multiple ground planes can be inserted to reduce the plane impedance and loop area.

Although power planes can be used as reference planes, ground is more effective because local stitching vias can be used for the return current transitions, rather than stitching decoupling capacitors which add inductance. This keeps the loop area small and reduces radiation. As the stackup layer count increases, so does the number of possible combinations of the structure. But, if one sticks to the basic rules, then the best performing configurations are obvious.

Figure 1 illustrates the spreading of return current density across the plane above and below the signal path. At high frequencies, the return current takes the path of least inductance. As the frequency approaches a couple of hundred MHz, the skin effect forces the return current to the surface (closest to the signal trace).

I previously mentioned that it is important to have a clearly defined current return path. But it is also important to know exactly where the return current will flow. This is particularly critical with asymmetric stripline configurations where one signal layer is sandwiched between two planes as in Figure 2. Now obviously, if the distance to the closest plane (h1) is the same distance as the far plane (h2) then the return current distribution will be equal on each plane (given the same inductance for each path). However, in order to force the current onto the ground (GND) plane of an unbalanced stripline configuration, h2 needs to be at least twice h1, and three times is better.

To read this entire column, which appeared in the August 2014 issue of The PCB Design Magazine, click here.

Share


Suggested Items

Signal Integrity: The Experts Weigh In

11/14/2017 | The I-Connect007 Team
When we began planning the October issue on signal integrity, we arranged a conference call with a variety of industry experts. Mike Steinberger of SiSoft, Mark Thompson of Prototron Circuits, and Yogen and Sunny Patel of Candor Industries joined editors Andy Shaughnessy, Patty Goldman, Happy Holden and Publisher Barry Matties on the call for a spirited discussion about the challenges related to signal integrity and some of the tricks of the trade for helping ensure SI.

Nine Dot Connects: Good Design Instruction is a True Value-Add

11/09/2017 | Andy Shaughnessy, PCBDesign007
Nine Dot Connects has certainly blazed an interesting trail. The company started out as an Altium reseller, but in less than a decade, Nine Dot Connects has also become a design service bureau and a provider of PCB design instruction, training, and consulting services. I recently interviewed Paul Taubman, technical services director for Nine Dot Connects. We discussed the company’s expansion from VAR to service bureau and content provider, and the changing landscape of PCB design instruction.

AltiumLive Summit—Munich, Germany, Part 1

11/07/2017 | Pete Starkey, I-Connect007
Altium held a very successful AltiumLive PCB Design Summit in San Diego, California at the beginning of October for the benefit of their North American design community, and followed it three weeks later with a counterpart European event in Munich. And what an eye-opener it proved to be—literally hundreds of delegates, a superbly organised and managed programme, billed as a completely immersive two-day interactive design experience on a theme of learning, connecting and getting inspired.




Copyright © 2017 I-Connect007. All rights reserved.