Innovative New Uses for Ceramic Column Grid Arrays from TopLine
December 18, 2015 | Andy Shaughnessy, I-Connect007Estimated reading time: 8 minutes
TopLine President and CEO Martin Hart sat down to discuss his paper on ceramic column grid arrays (CCGA) at the recent SMTA International show in Chicago. Hart begins by explaining the relationship between CCGA and ball grid arrays (BGA), and TopLine's drive to find new uses for CCGA.
Andy Shaughnessy: Martin, why don't you start by giving us a little background on CCGAs.
Martin Hart: The best way to talk about CCGAs is to reference their cousin, the BGA. Everybody is familiar with BGA—ball grid arrays. Few people realize that the CCGA, the ceramic column grid array, was actually invented about ten years before the first BGA. When BGA first came out, they were invented by Bell Laboratories; a full ten years after columns had already been in the field. The main purpose of having a column instead of a solder ball is to extend reliability. You get more temperature cycles out of a solder column because it will absorb the CTE mismatch between the materials of ceramic and substrate, such as an FR-4 PC board.
Shaughnessy: We just don't hear much about CCGA. Everybody seems to have settled on the BGA and flip chips and various other sorts of packaging. Why did the CCGA fall out of favor?
Hart: That's a good question. BGAs are lower cost and much easier to assemble. During the manufacturing process, attaching a solder ball is significantly easier than attaching a column. Solder balls roll and self-center onto the BGA pads. Columns are difficult to attach to the pads. They don't self-center because they are held rigidly in place, usually by a graphite tool, during the column attach process. Columns can easily get bend if handled incorrectly.
Shaughnessy: You have to literally stand this thing up.
Hart: You have to stand the column straight up during the attachment of the column to the substrate.
Shaughnessy: It sounds very risky, in a way.
Hart: There is an element of risk, but it’s more of a situation of having a correct manufacturing process. Your process has to be dialed to effectively use column grid arrays. Once you have a process in place, then CCGA seems to work well.
Shaughnessy: What is the new use that you seem to have found for them?
Hart: First I’ll tell you the traditional places where column grid arrays are used. Traditionally, they've been used in defense, military, aerospace and also in high-value computing. One new area is down-hole drilling, where you have electronics going down several miles. It's very hot as you go below the earth’s surface. There is also interest in specialized automotive where you have electronics in the firewall. Also, columns can be are found in some medical. Not medical implants in a human body, but in medical equipment. There is a benefit to use CCGA wherever you have a large ceramic package, and mounted on an FR-4 board or a polyimide board. CCGA is more reliable when the temperature swings dramatically.
If you have a very small ceramic, it's safe to use a BGA. I've researched and wrote some tables and calculations showing when it is safe to use a ceramic BGA and when you must use a CCGA. A small 15 mm square ceramic BGA will not cause any problem with solder ball delamination. But if you start to go larger, say a 35 mm square, 40 mm square, 45 mm or even larger, 50 mm square, then solder balls will delaminate. That will effectively create a catastrophic failure in the equipment.
I also want to point out that your equipment does not even have to be electrically switched on. Say, if your equipment is turned off, sitting in storage, then if you have a large ceramic part mounted with solder balls on an FR-4 board, then that equipment might fail. If your equipment is out in the elements experiencing alternating hot and cold temperatures, then your equipment might fail if it contains large ceramic BGA components. When the sun goes down, temperatures might drop -25 to -40°. And when the sun comes up temperatures might rise 100-125°. Just sitting in the box, you'll see the phenomenon of delamination with large ceramic BGA components.
Shaughnessy: What led you to focus more on CCGA?
Hart: The original business of TopLine was to manufacture process development kits of all kinds of parts, from BGA and QFP in a kit form with circuit boards. Customers, particularly in mil-defense, were asking for column grid arrays so they could perform their own process development. This has gone on for a number of years and we decided, "Okay, we need to jump in and address this market of producing CCGA and solder columns."
Shaughnessy: I guess CCGA would have its own completely different process.
Hart: Yes, it does. The process of attaching a column onto a ceramic substrate is totally different than attaching solder balls to a BGA. CCGA requires a graphite fixture to hold the column upright at a 90° angle. It involves having a controlled reflow process. We found that vapor phase reflow ovens are best solution because your maximum temperature is fixed. You can also use a twelve-zone oven, but you have to have that oven profile really dialed to attach solder columns.
Shaughnessy: How tall is this column?
Hart: Oh, good question. Traditionally, columns are 2.2 mm high. There's nothing totally magical about 2.2 mm high. Columns have been made 1.27 mm, which is 50 mills. Columns have been made bigger in diameter and smaller in diameter. IBM set the standard years ago with studies and of papers showing that 2.2 mm, is a good column height. The industry settled ever since. The secret is actually in the attachment process. You start with a longer column and then trim it down to 2.2 mm during the planarization process. After all the columns are attached in an array, you literally have to cut the columns shorter to planarize them. So you wind up with 2.2 mm, but you start off with a column that is 2.3 mm, up to 2.5 mm, in order to wind up with 2.2mm.
Page 1 of 2
Suggested Items
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
AIM Solder’s Dillon Zhu to Present on Ultraminiature Soldering at SMTA China East
04/22/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce that Dillon Zhu will present on the topic: Ultraminiature Soldering: Techniques, Technologies, and Standards at SMTA China East. This event is being held at the Shanghai World Expo Exhibition & Convention Center from April 24-25.
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.