-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Designing with Fine Lines and Features
July 13, 2016 | Andy Shaughnessy, PCBDesign007Estimated reading time: 2 minutes
Albert Gaines is the owner and senior PCB designer at HiGain Design Services in Norcross, Georgia. He’s been a PCB designer since 1981; he designed a variety of boards at Scientific Atlanta, and then ViaSat, before deciding to open his own company in metro Atlanta. I asked Albert to talk about some of the finer lines and features that come through his shop, as well as some design techniques for boards with tight tolerances.
Andy Shaughnessy: What are the tightest tolerances you are currently designing?
Albert Gaines: We have used 3.6 mil line and space on a few but most are 4 mil line and space for HDI.
Shaughnessy: What are the most challenging issues designers face regarding fine spaces, traces, and pitch?
Gaines: As we have progressed into smaller-pitch components, the space in and around components has decreased even more. These smaller areas drive what the vias and routes can be, and sometimes we are restricted by our clients and vendors on the sizes we can use. This may be a costing issue on the bare boards, or the smaller lines and vias may be restricted by an internal spec that was conceived before ultra-fine-pitch came to be. We have actually had to get chief technical officers sign off on the line/space and via sizes required for layouts.
Placing bypass capacitors for these finer-pitched parts can also be an issue. The pitch may drive the use of smaller body caps than the engineers or clients want to use. We end up placing caps all around the part because the application notes said to use this quantity and this value.
Shaughnessy: Do your PCB design tools handle tighter tolerances well? What about PCB design tools in general?
Gaines: Yes, we have tools that we can set up rules/constraints for those specific needs. In today's world, most higher-end tools allow you to set up rules/constraints for certain areas. This allows for those tight rules to be enforced in the area that drives that tight lines and spacing, while allowing more relaxed rules/constraints on the rest of the board. Setting up those rules could be made easier, but I appreciate what we have today to control layout, compared to what we had to use in the past.
I know you can find lower-end tools from a cost standpoint; however; these tools often do not have the features needed to perform the more complex mixed-technology boards required by our clients. I think the old saying “You get what you pay for” applies here. If you need the layout control, you may have to pay more for it.
To read this entire article, which appeared in the June 2016 issue of The PCB Design Magazine, click here.
Suggested Items
KIC’s Miles Moreau to Present Profiling Basics and Best Practices at SMTA Wisconsin Chapter PCBA Profile Workshop
01/25/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, announces that Miles Moreau, General Manager, will be a featured speaker at the SMTA Wisconsin Chapter In-Person PCBA Profile Workshop.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Standard Of Excellence: The Products of the Future
09/19/2023 | Anaya Vardya -- Column: Standard of ExcellenceIn my last column, I discussed cutting-edge innovations in printed circuit board technology, focusing on innovative trends in ultra HDI, embedded passives and components, green PCBs, and advanced substrate materials. This month, I’m following up with the products these new PCB technologies are destined for. Why do we need all these new technologies?
Experience ViTrox's State-of-the-Art Offerings at SMTA Guadalajara 2023 Presented by Sales Channel Partner—SMTo Engineering
09/18/2023 | ViTroxViTrox, which aims to be the world’s most trusted technology company, is excited to announce that our trusted Sales Channel Partner (SCP) in Mexico, SMTo Engineering, S.A. de C.V., will be participating in SMTA Guadalajara Expo & Tech Forum. They will be exhibiting in Booth #911 from the 25th to the 26th of October 2023, at the Expo Guadalajara in Jalisco, Mexico.
Intel Unveils Industry-Leading Glass Substrates to Meet Demand for More Powerful Compute
09/18/2023 | IntelIntel announced one of the industry’s first glass substrates for next-generation advanced packaging, planned for the latter part of this decade.