Challenges of DFM Analysis for Flex and Rigid-flex Design, Part 2
May 18, 2023 | Mark Gallant, DownStream TechnologiesEstimated reading time: 2 minutes
(Editor’s note: This is the second of a three-part series. To read Part 1, click here.)
Flex and Rigid-Flex: Different Layer Types
Everyday rigid FR-4 PCBs have a well-known layer stackup recipe: dielectrics, PCB conductor layers, plane layers, mask, and silkscreen (nomenclature or legend). More advanced layer types may include embedded or screened components or cavities with bonded bare die.
Flex and rigid-flex stackups include those similar to rigid PCBs, such as dielectrics, conductor, mask, and silkscreen layers, but that is where the similarity ends. There are many additional layer types present for this genre of PCB. They include types like coverlay, adhesive, conductive film, conductive foil, conductive adhesive, bondply, and stiffener.
- Coverlay: An external polyimide film that encapsulates and protects flexible conductor layers.
- Adhesive: Bonding agent used to bond copper foil to a polyimide substrate or coverlay.
- Conductive film: Transparent but electrically conductive film found in LCDs, touchscreens, and other optical applications.
- Conductive foil: Thin sheet of copper or silver commonly applied to a flexible PCB as shielding.
- Conductive adhesive: Adhesive applied for electrical interconnect, thermal or structural bonding applications.
- (Flexible) bondply: A polyimide film, coated both sides with B-staged acrylic adhesive. This is essentially a coverlay with adhesive on both sides.
- Stiffener: Blank FR-4 or other material bonded to flexible materials to add stiffness in a specific area.
These layer types are found in typical flexible PCB stackups. The presence of these layer types is not accounted for in most current DFM analysis. This is one area where specific DFM analysis is required. Rigid DFM analysis can detect issues with a solder mask but cannot be used to detect trace corners in a bend area.
Inter-layer Dependencies
While less common in rigid PCBs, flexible PCBs have many inter-layer dependencies that, if not managed well, may lead to manufacturing issues or field failures. The fabrication process used to bond rigid and flexible layers also has its inter-layer dependencies to be managed. Here are a few examples of inter-layer potential issues.
Squeeze-out
Even with best design considerations and best manufacturing practices, adhesive can “squeeze out” and bleed into unwanted areas on adjacent layers. Coverlay adhesive is a common source of squeeze-out that flows during lamination onto conductors, pads, cavities, fingers, or other features. This requires analysis that compares the size of coverlay exposure against the annular ring of adhesive below it.
To read this entire article, which appeared in the May 2023 issue of Design007 Magazine, click here.
Suggested Items
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
AIM Solder’s Dillon Zhu to Present on Ultraminiature Soldering at SMTA China East
04/22/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce that Dillon Zhu will present on the topic: Ultraminiature Soldering: Techniques, Technologies, and Standards at SMTA China East. This event is being held at the Shanghai World Expo Exhibition & Convention Center from April 24-25.
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.
Empowering Electronics Assembly: Introducing ALPHA Innolot MXE Alloy
04/16/2024 | MacDermid Alpha Electronics SolutionsIn the rapidly evolving electronics industry, where innovation drives progress, MacDermid Alpha Electronics Solutions is committed to setting a new standard. Today, we are pleased to introduce ALPHA Innolot MXE, a revolutionary alloy meticulously engineered to address the critical needs of enhanced reliability and performance in modern electronic assemblies.