Final Finishes: Taking Gold Thickness into Account
October 31, 2017 | Patty Goldman, I-Connect007Estimated reading time: 9 minutes
Bunce: Exactly, and we’ve been helping our customers understand these challenges over the last six months as the specification neared completion.
Goldman: How about educating the end-user who's specifying that they want this extra gold thickness?
Bunce: If you look at the participation in 4-14 Plating subcommittee, I'm estimating that OEMs make up over 50% of the contribution so you could say that the new specification has been driven by end user desires. However, there are OEMs, PCB fabricators and even chemistry suppliers who do not participate and some of the changes are likely to cause some shock.
Goldman: Okay, so the OEMs don't have a problem with this.
Bunce: From the end user point of view, if you're buying a more consistent product regarding gold thickness and corrosion, I think you're going to be a lot happier. From a PCB fabrication standpoint, there may be some further scrutiny of existing ENIG capability needed, but it should be achievable, maybe at a slightly higher cost.
Goldman: It sounds like, if they don't have the right measuring equipment, they can't measure their gold thickness properly?
Bunce: Measurement system evaluation for gold thickness is the starting point. A PCB fab first needs to understand their current capability and what it means in the number of required XRF measurements or a reduction in the gold thickness tolerance. If the number of measurements required (to conform to IPC-4552A) becomes excessive, and Capex for new instruments is not available, then the reduction in gold thickness tolerance may require adjustment to the ENIG process operation (or a change of process chemistry) to allow suitable gold thickness control.
Goldman: And it's almost too wide a range for what you're measuring?
Bunce: You can take up some of the gold thickness specification tolerance with measurement system variation. You can take up some of the tolerance with process variation. The more you take up with your measurement system variation, the more tightly you must control your ENIG process. That's something that we've addressed with development of the new MacDermid Enthone ENIG system—the ability to produce consistent gold thickness, basket to basket and pad to pad.
Producing an electroless nickel deposit with stable phosphorous content is key to meeting this challenge. Electroless nickel phosphorous content dictates the deposit’s corrosion resistance, so if we see significant variation in the phosphorous content then we see variation in corrosion resistance and thus variable gold thickness. We aim to produce a consistent 9% phosphorous over the electroless nickel chemical life to provide corrosion resistance stability and resultant gold thickness consistency.
Goldman: How do you maintain a 9% phosphorous in the nickel? How do you measure that?
Bunce: This is something the IPC has worked on. We've done a lot of round-robin testing. Traditionally, people used to use EDS to measure the phosphorous content of EN. If you look at some of the data produced by the committee, the amount of variation is quite frightening. Some XRF suppliers have supplied a simple-to-use XRF method that's fairly reliable—again discussed in the paper. And you can also strip the nickel and analyze the amount of phosphorous by a wet chemistry analysis but that's a real nuisance. The XRF method has been a bit of a godsend; maybe it's not as accurate as the wet analysis, but it's a hell of a lot quicker and non-destructive.
Goldman: That's important, too. I hope we get an opportunity to publish your paper in our magazine. Thank you very much for your time. I appreciate it.
Bunce: You’re welcome.
Page 2 of 2Suggested Items
Real Time with… IPC APEX EXPO 2024: My Role as a Technology Solutions Director
05/02/2024 | Real Time with...IPC APEX EXPOPeter Tranitz, senior director of technology solutions at IPC, shares insights into his role as the design initiative lead. He details his advocacy work, industry support, and the responsibilities of the design initiative committee. The conversation also covers the revamping of standards, the IPC Design Competition, and the implementation of design rules in software tools.
HQ NextPCB of HQ Electronics Debut on the International Stage for Electronics Manufacture at IPC APEX 2024
05/01/2024 | PRNewswireHQ NextPCB of HQ Electronics, a leading Chinese-based multilayer PCB manufacturer and assembly house showcased its industrial prowess on the international stage for the first time at the IPC APEX Expo 2024.
IPC's Vision for Empowering PCB Design Engineers
04/30/2024 | Robert Erickson, IPCAs architects of innovation, printed circuit board designers are tasked with translating increasingly complex concepts into tangible designs that power our modern world. IPC provides the necessary community, standards framework, and education to prepare these pioneers as they explore the boundaries of what’s possible, equipping engineers with the knowledge, skills, and resources required to thrive in an increasingly dynamic field.
North American EMS Industry Down 4% in March
04/29/2024 | IPCIPC announced the March 2024 findings from its North American Electronics Manufacturing Services (EMS) Statistical Program. The book-to-bill ratio stands at 1.31.
Real Time with… IPC APEX EXPO 2024: A Global Presence in PCB Manufacturing
04/29/2024 | Real Time with...IPC APEX EXPORob DiGiovanni, VP of sales for the Americas at STARTEAM Global, discusses the company's global presence in PCB manufacturing. As he explains, the firm operates facilities across Europe, Asia, and North America, specializing in serving contract manufacturers in the automotive and medical industries. They emphasize quality and meeting OEM standards, focusing on offshore supply and non-Chinese factories in the North American market. The company has grown through acquisitions and rebranding to offer multiple products.